Responsive image
博碩士論文 etd-0108108-173515 詳細資訊
Title page for etd-0108108-173515
論文名稱
Title
導光板製程參數與液晶顯示模組漣漪現象相關性研究
Research of the relation between the parameter of LGP injection and the ripple phenomena
系所名稱
Department
畢業學年期
Year, semester
語文別
Language
學位類別
Degree
頁數
Number of pages
74
研究生
Author
指導教授
Advisor
召集委員
Convenor
口試委員
Advisory Committee
口試日期
Date of Exam
2007-12-21
繳交日期
Date of Submission
2008-01-08
關鍵字
Keywords
漣漪、導光板
Ripple, LGP
統計
Statistics
本論文已被瀏覽 5736 次,被下載 5189
The thesis/dissertation has been browsed 5736 times, has been downloaded 5189 times.
中文摘要
近年來,由於未來市場針對液晶面板要求愈來愈輕薄的趨勢,液晶顯示模組厚度的要求成為一個需重視的問題,相對的愈薄的液晶顯示模組,因膜片的減少及導光板的厚度變薄,在外觀上愈容易顯現出問題,且因越薄的導光板越不易控制表面的平整度,也因表面平整度的不平均,造成液晶顯示模組在燒機實驗後常有漣漪現象發生。但是,卻無法在導光板單體時即發現此現象,直到導光板組到液晶顯示模組中,並進行燒機實驗後才察覺。而在此過程中已造成大量人力與物力的浪費。

本研究經由分析導光板單體在自由狀態、在背光模組中、在液晶模組並經過燒機實驗等不同情況下的高度差變化,並討論導光板成形之製程參數變異與產生漣漪現象的相互關係,以達到初期材料管控且漣漪現象不再發生的目的。
Abstract
Recently, the ripple phenomena of liquid crystal display module were occurred frequently after burning machine test. The phenomena were mainly caused by the non-uniformity of the flatness of light guide plate. But, it is difficult to detect the ripple phenomena when the light guide plate is in a free state. It is usually can be detected until the burning machine test of liquid crystal display module was finished. But it will cost massive manpower and the physical resource wasting in this process.

In this study, the through analyses of flatness variations of light guide plate in its free state, in the back light module, and in the liquid crystal display module after the burning machine test, respectively, were executed. Also, the effects of variations of process factors of a light guide plate on the ripple phenomena were studied. It is hoped to achieve the purpose that one can control the flatness of light guide plate in the initial stage so that the ripple phenomena will no longer occur.
目次 Table of Contents
中文摘要…………………………………………………Ⅰ英文摘要………………………………………………. Ⅱ 目錄…………………………………………………….Ⅲ
表說明…………………………………………………….Ⅳ
圖說明…………………………………………………….Ⅴ
第一章 緒論
1.1 前言.................................................................1
1.2 背光模組的主要元件及功用………………2
1.3 導光板的特性及可能所產生的影響……..3
1.4 文獻回顧…………………………………..5
1.5 研究動機與目的……………………….…..7
1.6 全文架構……………………………………7
第二章 實驗設備
2.1 三維空間量測儀...........................................12
2.2 掃瞄式表面量測儀........................................13
第三章 液晶顯示模組漣漪現象發生之原因
3.1 導光板表面平整度與漣漪現象的相對應關係之確認18
3.2 影響導光板表面平整度之製程參數............................20
3.3 導光板單體與導光板在模組內的差異確認...............21
3.4 導光板在燒機實驗前後的變化....................................22
3.5 時間與溫度的關連確認................................................23
第四章 導光板製程參數變異與產生漣漪現象的相互關係
4.1 導光板成形的冷卻時間實驗………….......................39
4.2 正翹度實驗....................................................................41
第五章 總結與未來展望
5.1 總結...............................................................62
5.2 未來展望.......................................................62
參考文獻..............................................................................64
參考文獻 References
1. 鍾俊元, “我國平面顯示器產業2006年回顧與2007年第一季展望”,平面顯示器,工研院IEK電子組,2007/03/08
2. 葉錦清,Display Research, 2007
3. B. Scibilia, A. Kobi, R. Chassagnon and A. “Barreau, Designed Fatigue Experiments to Improve the Reliability of Liquid Crystal Displays”, Reliability and Maintainability Symposium, Vol.24-27, pp.234-238, 2000
4. W. Ren and J. Wang, “Assembly-Induced Stress and Its Effect on the Integrity of Assembly System in Drop Simulation, Mechanical and Multiphysics Simulation and Experiments in Micro-Electronics” , EuroSimE 2006, p 1643977, 2006
5. J. Wu, G. Song, C.P. Yeh and K. Wyatt, “Drop Impact Simulation and Test Validation of Telecommunication Products, Inner Society Conference on Thermal Phenomena, Vol.27-30, pp.330-336, 1998
6. C.Y. Chu, M. C. Pan and J. Ho, “Thermal Analysis and Experimental Validation on TFT-LCD Panels for Image Quality Concerns”, Electronic Packaging Technology Conference, Vol.2, No.7-9 Dec, 2005
7. 錢志回,曾昱銘,蔡明朗,謝其昌, “熱變形對LCD導光板特性之影響”, 第二十九屆中華民國力學學會年會暨全國力學會議, 國立清華大學,新竹,2005
8. G.H. Kim, “A PMMA composite as an optical diffuser in a liquid crystal display backlighting unit(BLU) ”, European Polymer Journal, pp.1729-1737, 2005
9. G.H. Kim, W. J. Kim, S. M. Kim and J. G. Son, “Analysis of thermo-physical and optical properties of a diffuser using PET/PC/PBT copolymer in LCD backlight units”, Displays, pp.37- 43, 2005
10. 蘇佩君,液晶顯示器背光模組之膜片翹曲現象分析,碩士論文,國立中山大學機械與機電工程學系,高雄,2004
11. 馮文宏,楔形板件於精密射出與射出壓縮成型之探討,碩士論文台灣大學機械工程研究所,台北,2001
12. 吳政憲,射出壓縮成型應用於厚度不均光學元件之製程研究,國科會計劃,大葉大學機械工程學系,彰化,2002
13. 張永彥,塑膠模具設計學,全華科技圖書有限公司,台北,2005
14. 簡華佐,射出成形模澆口位置最佳化之探討,碩士論文,國立台灣科技大學機械工程系,台北,2006
15. 黃臣鴻,PC/ABS合膠機械性質之射出成型條件最佳化,博士論文,國立中央大學機械工程研究所,中壢,2003
16. Y. Hioe, Mold thermal design and quasi steady state cycle time analysis in injection molding, master thesis, Industrial and system Engineer, Ohio State University, 2006
17. D.H. Harry, and R.G. Parrott, “Numerical Simulation of Injection Mold Filling”, Polymer Engineering and Science, Vol.10,No.1,pp.209-241, 1970.
18. M.R. Kamal,. and S. Kenig, “The Injection Molding of Thermo-Plastics Part I: The Theoretical Model”, Polymer Engineering and Science,Vol.12, No.1,pp.294-301,1972.
19. P. Thienel, and G. Menges, “Mathematical and Experimental Determination of Temperature, Velocity and Pressure Fields in Flat Molds During the Filling Process in Injection Molding of Thermo-plastics”, Polymer Engineering and Science,Vol.18,No.1,pp. 314-320,1978.
20. 吳政憲等人,射出成型應用於導光板之製程研究,大葉大學機械與自動化工程研究所/塑膠工業技術發展中心,2007
21. 黃東鴻,Study on Warpage & Residual Stress of Thin-walled Injection Molding,碩士論文,國立成功大學航空太空工程研究所,台南,2002
22. 葉清民,精密塑膠射出成形最佳參數之數學理論,雄工學報第八輯
23. E.Lindner, and P.Unger, “Injection Molds 108 Proven Designs”, 1993,pp6-13
24. C-Mold Injection User’s Guide, 1999, AC Technology Ithaca, New York, U.S.A. 1999. C-MOLD 99.
25. 鐘清章著; 田口式品質工程導論,中華民國品質學會,台北,1997
26. 吳復強著; 產品穩健設計-田口方法之原理與應用,全威圖書有限公司,台北,2005
27. 陳耀茂譯; 田口實驗計劃法,滄海書局,台中,1997
28. 方育斌,LCD 背光模組之光學最佳化設計,碩士論文,國立成功大學機械工程學系,台南,2004
29. 蔡耀葳,LCD 背光模組中稜鏡片之結構設計,碩士論文,國立中山大學機械與機電工程學系,高雄,2005
30. 徐梓青,FC-BGA 構裝體的數值分析與最佳化研究,碩士論文,國立成功大學機械工程學系,台南,2004
電子全文 Fulltext
本電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。
論文使用權限 Thesis access permission:校內校外完全公開 unrestricted
開放時間 Available:
校內 Campus: 已公開 available
校外 Off-campus: 已公開 available


紙本論文 Printed copies
紙本論文的公開資訊在102學年度以後相對較為完整。如果需要查詢101學年度以前的紙本論文公開資訊,請聯繫圖資處紙本論文服務櫃台。如有不便之處敬請見諒。
開放時間 available 已公開 available

QR Code