Responsive image
博碩士論文 etd-0209112-230302 詳細資訊
Title page for etd-0209112-230302
論文名稱
Title
內嵌式碳化鎢刀具對低碳鋼摩擦攪拌點銲接之研究
Studies on Friction Stir Spot Welding of Carbon Steel Using Inserted-Type Tungsten Carbide Tools
系所名稱
Department
畢業學年期
Year, semester
語文別
Language
學位類別
Degree
頁數
Number of pages
81
研究生
Author
指導教授
Advisor
召集委員
Convenor
口試委員
Advisory Committee
口試日期
Date of Exam
2011-07-25
繳交日期
Date of Submission
2012-02-09
關鍵字
Keywords
摩擦攪拌點銲接、內嵌式銲接工具、低碳鋼、搭接、碳化鎢工具
Tungsten Carbide Tools, Lap Joint, Low-Carbon Steel, Friction Stir Spot Welding, Inserted-Type Tools
統計
Statistics
本論文已被瀏覽 5649 次,被下載 397
The thesis/dissertation has been browsed 5649 times, has been downloaded 397 times.
中文摘要
本研究設計一嶄新之內嵌式銲接工具,以進行對4mm之SS400低碳鋼薄板進行摩擦攪拌單點銲接。為了提升其生成摩擦熱的效率以及增進銲接點銲接品質,銲接工具以直徑20mm碳化鎢圓棒為基礎,在肩部嵌入一塊SS400低碳鋼圓柱形嵌料。銲接設備使用ㄧ具有定負荷銲接平台之立式銑床。銲接時工具與試片間正向負荷為8kN,工具沒有傾角;銲接過程工具擠入深度和銲接界面溫度分別以位移計與熱電偶進行動態量測。

  以工具轉速900rpm銲接60秒下,使用嵌料直徑5mm和10mm之溫度升高的速率分別是沒有嵌料銲接工具的5.28和6.31倍;以1200rpm銲接則為1.36和1.42倍。而在銲接300秒後,使用嵌料直徑5mm和直徑10mm所到達的最高銲接溫度比沒有嵌料銲接工具升高59℃和412℃;以1200rpm銲接則為35.6℃和197.6℃。在銲接工具轉速銲接60秒下,以轉速900rpm使用嵌料直徑5mm和直徑10mm所得之銲接試片剪切方向破壞負荷分別比沒有嵌料銲接工具高11.3kN和15.5kN,攪拌層厚度也增加2mm和5mm;以轉速1200rpm下使用嵌料直徑5mm和直徑10mm所得之銲接試片剪切方向破壞負荷分別比沒有嵌料銲接工具高7.6kN和18.3kN。
Abstract
This study aims to design a novel inserted welding tool to friction stir spot weld SS400 low carbon steel sheets of 4mm thickness. In order to enhance the efficiency of frictional heat generation and to enhance the quality of the welding spot, the welding tool based on a cylindrical tungsten carbide and is inserted by a SS400 low carbon cylinder. The welding apparatus composed of a vertical milling machine and a welding platform that can keep the load between tool and workpiece constant. The plunge load is 8kN and there's no inclination angle on the tools. Welding temperature and the tool plunge depth are measured by thermelcouples and a displacement meter.
  At the tool rotational speed of spindle of 900rpm and welding for 60 seconds, the temperature rising rate of the tools with 5 mm and 10 mm inserted material are 5.28 times and 6.31 times greater than the one without insert. While they are 1.36 and 1.42 times greater than at 1200rpm.At the tool rotational speed of spindle of 900rpm and welding for 300 seconds, themaximun welding temperature the tools with 5 mm and 10 mm inserted material can reach are 59℃ and 412℃ higher than the one without insert. While they can reach 35.6℃ and 197.6℃ greater than at 1200rpm. According to the tensile test, the shear failure loads of clad steel plates increase 11.3kN and 15.5kN by using tools with 5 mm and 10 mm inserted material at 900rpm for 60 seconds, and increase 7.6kN and 18.3kN by using tools with 5 mm and 10 mm inserted material at 1200rpm.
目次 Table of Contents
總 目 錄
論文審定書 i
誌謝 ii
中文摘要 iii
英文摘要 iv
總目錄 v
圖目錄 viii
表目錄 xii
符號說明 xiii
第一章 緒論 1
1.1 前言 1
1.2 文獻回顧 4
1.2.1 摩擦攪拌點銲接 4
1.2.2 回填式摩擦攪拌點銲接 7
1.2.3 銲接工具材料選用 11
1.2.4 銲接工具外形設計 15
1.3 研究目的 19
1.4 論文架構 20
第二章 實驗設備與方法 21
2.1 實驗設備 21
2.1.1 定負荷銲接平台 22
2.1.2 位移量測設備 24
2.1.3 溫度量測設備 24
2.1.4 擠入深度、溫度量測系統配線 25
2.2 實驗試片之材料特性與尺寸 26
2.3 銲接工具之設計 27
2.4 背部墊板之材料特性與尺寸 29
2.5 實驗方法 30
2.5.1 實驗參數規劃 30
2.5.2 試片前處理 31
2.5.3 實驗步驟 32
2.5.4 銲接試片放置與銲接位置 34
2.5.5 K-Type熱電偶之放置 35
2.5.6 金相觀察試片準備 36
2.6 實驗流程 37
第三章 實驗結果與討論 38
3.1 溫度、擠入深度動態量測值之探討 38
3.1.1 不同嵌料直徑銲接工具之銲接界面溫度變化 38
3.1.2 擠入深度與銲接介面溫度之關係 43
3.2 銲點表面與橫切面光學觀察 52
3.2.1 不同嵌料直徑銲接工具對銲點外觀之影響 52
3.2.2 不同嵌料直徑銲接工具對塑性流動層厚度之影響 54
3.3 剪切力試驗與破斷面觀察 56
3.3.1 不同嵌料直徑銲接工具對銲點剪切力之影響 56
3.3.2 不同嵌料尺寸銲接試片剪斷面分析 68
第四章 結論與結論與未來之發展 60
4.1 結論 60
4.2 未來之發展 62
參考文獻 63
參考文獻 References
【1】 W. M. Thomas, E. D. Nicholas, J. C. Needham, M. G. Murch, P. Templesmith, and C.    J.Drawes, 〝Friction Stir Butt Welding〞, G B Patent Application No. 9125978.8, Dec.1991; S.S. Patent No. 5460317, Oct., 1995.
【2】 W. M Thomas, E. D. Nicholas, R. E. Dolby, C. J. Jones, R. H. Lilley, 〝Friction Plug Extrusion〞, InterntionalPatent PCT/GB92/01540.21.8.92 R.S. Mishra, and Z.Y. Ma, 〝Friction stir welding and processing〞, Materials Science and Engineering: R: Reports 50 (2005) 1-78.
【4】 林耀隆, 〝摩擦攪拌銲接過程之作用力和攪拌能量之實驗研究〞, 中山大學機械
與機電工程研究所碩士論文, 2006
【5】 F. Hunt, H. Badrinarayan, and K. Okamoto, 〝Design of Experiments for Friction StirStitch Welding of Aluminium Alloy 6022-T4〞, Paper 2006-01-0970, 2006 SAE World Congress (Detroit, MI), Society of Automotive Engineers
【6】 T. Iwashita, 〝Method and Apparatus for Joining〞, U.S. Patent 6,601, 751, 2003
【7】 The Aluminium Association,〝Mazda the First to Use Friction Stir Welding for Aluminium Body Assembly〞,Aluminium Now Online 5 (2003)
【8】 C. Shilling and J. dos Santos, 〝Method and Device for Joining at Least Two Adjoining Work Pieces by Friction Welding〞, U.S. Patent Application 2002/0179682
【9】 K. Okamoto, F. Hunt, and S. Hirano, 〝Development of Friction Stir Welding Technique and Machine for Aluminium Sheet Metal Assembly〞, Paper 2005-01-1254, 2005 SAE World Congress (Detroit, MI), Societyof Automotive Engineers
【10】 C.D. Allen, and J.A. Arbegast, 〝Evaluation of Friction Spot Welds in Aluminium Alloys〞, Paper 2005-01-1252, 2005 SAE World Congress (Detroit, MI), Society of Automotive Engineer
【11】 Y. Uematsu, K. Tokaji, Y. Tozaki, T. Kurita, and S. Murata, 〝Effect of re-flling probe hole on tensile failure and fatigue behaviour of friction stir spot welded joints in Al-Mg-Si alloy〞, International Journal of Fatigue 30 (2008) 1956-1966
【12】 T. Rosendo, B. Parra, M. A. D. Tier, A. A. M. da Silva, J. F. dos Santos, T. R.    Strohaecker, and N.G. Alcantara, 〝Mechanical and microstructural investigation of     friction spot welded AA6181-T4 aluminium alloy〞, Materials and Design 32 (2011)     1094-1100
【13】 M. A. Sutton, A.P. Reynolds, J. Yan, B. Yang, and N. Yuan, 〝Microstructure and Mixed Mode I/II Fracture of AA2524-T351 Base Material and Friction Stir Welds〞, Engineering Fracture Mechanics 73 (2006) 391-407
【14】 A.P. Reynolds, W. Tang, T. Gnaupel Herold, and H. Prask, 〝Structure, Properties, and Residual Stress of 304L Stainless Steel Friction Stir Welds〞, Scripta Metallurgica 48 (2003) 1289-1294
【15】 M.W. Mahoney, W.H. Bingel, S.R. Sharma, and R.S. Mishra, 〝Microstructural Modification and Resultant Properties of Friction Stir Processed Cast NiAl Bronze〝, Materials Science Forum 426 (2003) 2843-2848
【16】 H. Fujii, Y. Takada, N. Tsuji, and K. Nogi, 〝Friction Stir Welding of Ultrafine Grained Materials〞, Proceedings of the Fifth International Conference on Friction Stir Welding, Sept 14-16, 2004 (Metz, France)
【17】 M. Fukumoto, T. Yasui, Y. Shimoda, M. Tsubaki, and T. Shinoda, 〝Butt Welding Between Dissimilar Metals by Friction Stirring〞, Proceedings of the Fifth International Conference on Friction Stir Welding, Sept 14-16, 2004 (Metz, France)
【18】 T. Yasui, T. Ishii, Y. Shimoda, M. Tsubaki, M. Fukumoto, and T. Shinoda, 〝Friction Stir Welding Between Aluminum and Steel with High Welding Speed〞, Proceedings of the Fifth International Conference on Friction Stir Welding,Sept 14-16, 2004 (Metz, France)
【19】 H.J. Liua, J.C. Fenga, H. Fujii, and K. Nogi, 〝Wear characteristics of a WC-Co tool in friction stir welding of AC4A+30 vol%SiCp composite〞, International Journal of Machine Tools & Manufacture 45 (2005) 1635-1639
【20】 A.K. Lakshminarayanan, V. Balasubramanian, and M. Salahuddin, 〝Microstructure, Tensile and Impact Toughness Properties of Friction Stir Welded Mild Steel〞, Journal of Iron and Steel Research, Iternational 17 (2010) 68-74
【21】 D.H. Choi, C.Y. Lee, B.W. Ahn, J.H. Choi, Y.M. Yeon, K. Song, H.S. Park, Y.J. Kima, C.D. Yoo, and S.B. Jung, 〝Frictional wear evaluation of WC-Co alloy tool in friction stir spot welding of low carbon steel plates〞, Int. Journal of Refractory Metals & Hard Materials 27 (2009) 931-936
【22】 P. Konkol, 〝Characterization of Friction Stir Weldments in 500 Brinell Hardness Quenched and Tempered Steel, Proceedings of the Fourth International Conference on Friction Stir Welding〞, May 14-16, 2003 (Park City, UT)
【23】 M.P. Miles, J. Pew, T.W. Nelson, and M. Li, 〝Formability of Friction Stir Welded Dual Phase Steel Sheets〞, Friction Stir Welding and Processing III (2005) 91-96
【24】 M. Collier, R. Steel, T. Nelson, C. Sorensen, and S. Packer, 〝Grade Development of Polycrystalline Cubic Boron Nitride for Friction Stir Processing of Ferrous Alloys〞, Materials Science Forum 426 (2003) 3011-3016
【25】 C.D. Sorenson, T.W. Nelson, S.M. Packer, and R.J. Steel, 〝Innovative Technology Application in FSW of High Softening Temperature Materials〞, Proceedings of the Fifth International Conference on Friction Stir Welding, Sept 14-16, 2004 (Metz,France)
【26】 Y. Zhang, Y.S. Sato, H. Kokawa, S.H.C. Park, and S.Hirano, 〝Stir zone microstructure of commercial purity titanium friction stir welded using pcBN tool〞, Materials Science and Engineering 488 (2008) 25-30
【27】 Y. Hovanski, M.L. Santella and G.J. Grant, 〝Friction stir spot welding of hot-stamped boron steel〞, Scripta Materialia 57 (2007) 873-876
【28】 C.J. Dawes, P.L. Threadgill, E.J.R. Spurgin, and D.G. Staines, 〝Development of the New Friction Stir Technique for Welding Aluminum—Phase II〞, TWI member report 5651/35/95, Nov 1995
【29】 J. Yan, M.A. Sutton, and A.P. Reynolds, 〝Process-Structure-Property Relationships for Nugget and Heat Affected Zone Regions of AA2524-T351 Friction Stir Welds〞, Science and Technology of Welding & Joining 10 (2005) 725-736
【30】 R.A. Prado, L.E. Murr, A.R. Rivera, D.J. Shindo, K.F. Soto, G.J. Fernandez, and J.C. McClure, 〝Tool Wear and Shape Optimization in the Friction-Stir Welding of Aluminum Metal-Matrix Composite〞, Friction Stir Welding and Processing II (2003) 23-32
【31】 I. Charit and R.S. Mishra, 〝Low Temperature Superplasticity in a Friction Stir Processed Ultrafine Grained Al-Zn-Mg-Sc Alloy〞, Acta Materialia 53 (2005) 4211-4223
【32】 H. Badarinarayan, Y. Shi, X.Li, and K. Okamoto, 〝Effect of tool geometry on hook formation and static strength of friction stir spot welded aluminum 5754-O sheets〞, International Journal of Machine Tools & Manufacture 49 (2009) 814-823
【33】 M.A. Sutton, A.P. Reynolds, B. Yang, and R. Taylor, 〝Mode I Fracture and Microstructure for 2024-T3 Friction Stir Welds〞, Material Science Engineering 354 (2003) 6-16
【34】 S.H.C. Park, Y.S. Sato, H. Kokawa, K.Okamoto, S. Hirano, and M. Inagaki, 〝Corrosion Resistance of Friction Stir Welded 304 Stainless Steel〞, Scripta Metallurgica 51 (2004) 101-105
【35】 S.P. Vaze, J. Xu, R.J. Ritter, K.J. Colligan, J.J. Fisher, Jr., and J.R. Pickens, 〝Friction Stir Processing of Aluminum Alloy 5083 Plate for Cold Bending〞, Materials Science Forum 426 (2003) 2979-2986
【36】 K.J. Colligan and J.R. Pickens, 〝Friction Stir Welding of Aluminum Using a Tapered Shoulder Tool〞, Friction Stir Welding and Processing III (2005) 161-170
【37】 H. Badarinarayan, Q. Yang, and S. Zhu, 〝Effect of tool geometry on static strength of friction stir spot-welded aluminum alloy〞, International Journal of Machine Tools & Manufacture 49 (2009) 142-148
【38】 K. Aota, and K.Ikeuchi, 〝Development of friction stir spot welding using rotating tool without probe and its application to low-carbon steel plates〞, Welding International 23 (2009) 572-580
【39】 Y. Tozaki, Y. Uematsub, and K. Tokaji, 〝A newly developed tool without probe for friction stir spot welding and its performance〞, Journal of Materials Processing Technology 210 (2010) 844-851
【40】 H. Schimidt, J. Hattel, and J. Wert, 〝An analytical model for the heat generation in friction stir welding〞, Materials Science and Engineering 12 (2004) 143-157
【41】 A. P. Reynolds, W. Tang, Z. Khandkar, J. A. Khan and K.Linder, 〝Relationships between weld parameter, hardness distribution and temperature history in alloy 7050 friction stir welds〞, Science and Technology of Welding and Joining 10 (2005) 190-199
電子全文 Fulltext
本電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。
論文使用權限 Thesis access permission:自定論文開放時間 user define
開放時間 Available:
校內 Campus: 已公開 available
校外 Off-campus: 已公開 available


紙本論文 Printed copies
紙本論文的公開資訊在102學年度以後相對較為完整。如果需要查詢101學年度以前的紙本論文公開資訊,請聯繫圖資處紙本論文服務櫃台。如有不便之處敬請見諒。
開放時間 available 已公開 available

QR Code