Responsive image
博碩士論文 etd-0806116-095704 詳細資訊
Title page for etd-0806116-095704
論文名稱
Title
使用導電高分子工具電解複合磨粒拋光純鋁圓柱面之研究
Studies of Electrochemical Abrasive Polishing on the Cylindrical Surface of Aluminum Using Conductive Polymer Tool
系所名稱
Department
畢業學年期
Year, semester
語文別
Language
學位類別
Degree
頁數
Number of pages
70
研究生
Author
指導教授
Advisor
召集委員
Convenor
口試委員
Advisory Committee
口試日期
Date of Exam
2016-07-25
繳交日期
Date of Submission
2016-09-08
關鍵字
Keywords
磨粒拋光、電解拋光、電解複合磨粒拋光、導電高分子
abrasive polishing, electro-polishing, composite electrolytic abrasive polishing, conductive polymer
統計
Statistics
本論文已被瀏覽 5736 次,被下載 1
The thesis/dissertation has been browsed 5736 times, has been downloaded 1 times.
中文摘要
純鋁材料因其優異的機械性質常應用於各種先進工業中,而純鋁材料拋光大多使用化學拋光及電解拋光,此兩種拋光方法所使用溶液通常具毒性且不可回收,本研究使用一無毒環保之電解液進行電解拋光與電解複合磨粒拋光。純鋁平板電解實驗結果顯示使用磷酸酒精溶液作為電解液可以得到最佳的表面粗糙度。
使用導電高分子作為工具電極,進行三種不同純鋁圓柱面拋光,包括磨粒拋光、電解拋光及電解複合磨粒拋光。磨粒拋光實驗中討論不同加工負荷對表面粗糙度的影響,實驗結果得到以0.3 μm Al_2 O_3磨粒進行拋光在負荷0.1 N下加工6分鐘可以得到最佳表面粗糙度Ra=0.076 μm,Rmax=0.53 μm。電解拋光實驗中比較不同加工電流下表面粗糙度結果,結果顯示加工電流0.15 A時加工6分鐘後可得到較佳之表面粗糙度,Ra=0.086 μm,Rmax=0.61 μm。
電解複合磨粒拋光分別選用磨粒拋光與電解拋光中最佳參數,亦即在0.3 μm Al_2 O_3磨粒與磷酸酒精溶液中使用加工負荷0.1 N與加工電流0.15 A進行實驗,加工6分鐘後可得到最佳表面粗糙度,Ra=0.053 μm,Rmax=0.48 μm,驗證透過磨粒與電解兩者機制同時進行可有效達成純鋁圓柱面之拋光。
Abstract
Pure aluminum is often applied in various advanced industry due to its excellent mechanical properties. Two polishing methods are usually used, including chemical polishing and electro-polishing, but the solutions used by them are generally toxic and not recyclable. In this study, a non-toxic electrolyte is used to conduct the electrolytic polishing and the composite electrolytic abrasive polishing. In the electrolytic experiments for aluminum plate, the phosphoric acid and ethanol solution is the optimal electrolyte to obtain the best surface roughness.
Three different methods are conducted to polish the cylindrical surface of pure aluminum using a conductive polymer as a cathode, including abrasive polishing, electrolytic polishing, and composite electrolytic abrasive polishing. The effect of load on the surface roughness is investigated in the abrasive polishing experiments. Results show that the optimal surface roughness can achieve Ra=0.076 μm and Rmax=0.53 μm at 0.1 N load with 0.3 μm Al_2 O_3 particles after 6 minutes. In the electrolytic polishing experiments, the optimal surface roughness can achieve Ra=0.086 μm and Rmax=0.61 μm at 0.15 A current after 6 minutes.
In the composite electrolytic abrasive polishing, the optimal parameters obtained by the abrasive polishing and the electrolytic polishing are selected. Hence, the composite electrolytic abrasive polishing is conducted under 0.1 N load and 0.15 A current with 0.3 μm Al_2 O_3 particles mixed in phosphoric acid and ethanol solution. The surface roughness can achieve Ra=0.053 μm and Rmax=0.48 μm after 6 minutes. This study confirms that both polishing mechanism of abrasive and electrolysis are effective to polish the cylindrical surface of pure aluminum.
目次 Table of Contents
論文審定書 i
誌謝 ii
摘要 iii
Abstract iv
目錄 v
圖次 vii
表次 ix
第一章 緒論 1
1.1 研究背景 1
1.2 文獻回顧 4
1.2.1 電化學加工 4
1.2.2電解複合磨粒拋光 6
1.2.3 以導電高分子作為工具電極 8
1.3 研究目的 9
第二章 實驗裝置與實驗方法 10
2.1 純鋁平板電解實驗 10
2.1.1 電解實驗設備 10
2.1.2 工件材料特性與幾何尺寸 11
2.1.3 電解實驗系統 12
2.1.4 粗糙度量測設備 13
2.1.5 實驗步驟 14
2.2 純鋁圓柱面拋光實驗 15
2.2.1 實驗設備 15
2.2.2 實驗系統 16
2.2.3 實驗工件幾何形狀與尺寸 17
2.2.4 量測設備 18
2.2.5 工具電極設計 19
2.2.6 實驗步驟 20
第三章 實驗結果與討論 22
3.1 純鋁平板電解實驗 22
3.1.1 電解液選用 22
3.1.2 電解液攪拌效應 31
3.1.3 時間效應 32
3.1.4 電流電壓特性分析 33
3.2 純鋁圓柱面拋光–磨粒拋光 37
3.2.1 負荷效應 38
3.2.2 時間效應 39
3.2.3 加工機制 39
3.3 純鋁圓柱面拋光–電解拋光 46
3.3.1 電流效應 47
3.3.2 時間效應 48
3.3.3 加工機制 48
3.4 電解複合磨粒拋光 53
第四章 結論與未來方向 57
4.1 結論 57
4.2 未來方向 58
參考文獻 59
參考文獻 References
[1] Rosemary Gene, Aaron J, “Faraday's electrochemical laws and the determination
of equivalent weights”, Journal of Chemical Education, vol. 31, issue 5, p. 226.
[2] H Figour, P. A. Jacquet, French Patent No.707526 (1930).
[3] W. C. Elmore, “Electrolytic Polishing” , J. appl. Phys10, 724 (1939); 11, 799 (1940).
[4] T. P. Hoar, G. P. Rothwell, “The Influence of Solution Flow on Anodic Polishing. Copper in Aqueous o-phosphoric acid ”, Electrochim Acta 9,135(1964).
[5] I. Epelboin, proc. Surface 66, p. 161. Foster, Zürich (1966).
[6] J. Edwards, J. electrochem. Soc, 100,189C, 223C (1950).
[7] W. J. McTegart, “The Electrolytic and Chemicl Polishing of Metals”, Pergamon
Press, London (1956).
[8] P. V. Shigolev, “Electrolytic and Chemical Polishing of Metals”, 2nd edn. Freund
Publ. Tel-Aviv, Israel (1974).
[9] C.L. Faust, “Electro-polishing I: The practical side”, Metal Finishing, (1982)
21-25.
[10] C.L. Faust, “Electro-polishing II: The practical side”, Metal Finishing, (1982)
59-63.
[11] 前畑英彦, 釜田浩 與 山本昌彦,“電解複合鏡面加工の研究”,精密工学
会,51(1985) 136-143.
[12] 清宮紘一,“電解砥粒研磨による鋼材の精密鏡面仕上げ”,鉄と鋼, 72
(1986) 904-908.
[13] 馬場吉康, 佐藤憲二,“電解複合研磨による金属の超鏡面化技術”,表
面科学, 11 (1990) 368-374.
[14] 木本康雄, 垣野義昭 及 中川真二,“高精度電解複合鏡面加工の研究”
,精密工学会誌,,2 (1988) 353-358.
[15] M.A. Laboda and M.L. Mcillan, “A new electrolyte for electrochemical
machining”, 5 (1967) 340-345.
[16] A.R. Mileham, S.J. Harvey and K.J. Stout, “The characterization of
electrochemically machined surfaces”, Wear, 109 (1986) 207-214.
[17] H. Shirakawa, E.J. Louis, A.G. Macdiarmid, C.K. Chiang, A.J.
Heeger, “Synthesis of Electrically Conducting Polymers: Halogen Derivatives of
Poly-acetylene, (CH)X”, Journal of The Society-Chemical Communications,16
(1977) 578-580.
[18] Wazer Van, “Viscosity and flow measurement”, Interscience Publisher, (1963)
189-191.
[19] 曾信智,“黏彈性磨料應用於複雜曲面的精拋技術研究”,國立中央大學
機械工程研究所博士論文,(2006).
[20] 蔡芯穎,“使用導電高分子工具於電解複合研磨的鋼之表面特性研究”,,國
立中山大學機械與機電工程研究所碩士論文,(2011).
[21] 李承祐,“電解擦光加工參數對304不銹鋼表面粗糙度之影響”,國立中山
大學機械與機電工程研究所碩士論文,(2012).
[22] 魏展鴻, “使用導電高分子工具對不鏽鋼表面的電解擦光之研究”, 國立中
山大學機械與機電工程研究所碩士論文,(2013).
[23] 杜致緯, “使用導電高分子工具電解複合磨粒拋光圓桿件之研究”, 國立中
山大學機械與機電工程研究所碩士論文,(2014).
電子全文 Fulltext
本電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。
論文使用權限 Thesis access permission:自定論文開放時間 user define
開放時間 Available:
校內 Campus: 已公開 available
校外 Off-campus:永不公開 not available

您的 IP(校外) 位址是 54.242.191.214
論文開放下載的時間是 校外不公開

Your IP address is 54.242.191.214
This thesis will be available to you on Indicate off-campus access is not available.

紙本論文 Printed copies
紙本論文的公開資訊在102學年度以後相對較為完整。如果需要查詢101學年度以前的紙本論文公開資訊,請聯繫圖資處紙本論文服務櫃台。如有不便之處敬請見諒。
開放時間 available 永不公開 not available

QR Code