由於目前碳纖維高爾夫球桿廠商對其所出廠的球桿皆有一套標準的量測方試，主要就是為了檢視球桿有無達到廠商的要求規格。彎曲：依序在大小端固定，在其相反的一端施予一重物塊，分別量測其變形量；扭矩：在小端給予一扭轉力矩，再測量其扭轉角；振動：在球桿小端懸掛一重物塊，再給予一擾動使其振盪，再量測其振盪次數。
碳纖維高爾夫球桿的模型的建立與機械性質的模擬都使用有限元素軟體“ANSYS”來建立與求解，主要為靜態與模態方面的運算來模擬球桿的機械性質，並將求解的結果與實驗的數據進行比對，再改變球桿內層、中層、與外層的疊層角度，探討對球桿機械性質的影響。
在本文裡，由有限元素軟體“ANSYS”所求得的變形量的值、扭轉角度、與每分鐘的振盪次數和實驗所測得的數據只有10%不到的誤差，也可知模擬值是可靠的，而由模擬值也可知高爾夫球桿的疊層角度和機械性質的關聯性是非常大的，所以本文也做出一系的數據與趨勢圖供廠商參考與應用。

Many golf firms of carbon fiber golf shafts are much concerned about for standard measurement of shafts for their specific needs. To achieve the purpose, the present study was conducted. Flex：The researcher first hanged a mass on the tip with the butt fixed, and then he hanged a mass on the butt with the tip fixed for measuring the deflection of the shaft. Torque：The degree of torsion is measured by applying the twisting moment 0.126 (kgf•m) to the tip. Vibration：The cycle per minute is measured by adding a mass to the tip of a shaft and shaking it.
The mechanical performance of carbon fiber composite is modeled and solved by the finite element software “ANSYS” in static and modal analysis. The errors between the simulations and experiments were compared and discussed. Finally, the angles of in, middle, and out layers of the shaft were changed to see how they affect the mechanical performance of golf shafts.
In this study, the errors of the results for deflection, degree of torsion, and cycle per minute of golf shafts between experiments and simulations are less than 10%. The results solved by the finite element software “ANSYS” are reliable. The results of simulations also show that a close relationship between the mechanical performance of golf shafts and the fiber angles. Eventually, a series of data bases and trend pictures were provided for golf firms' reference and application.

目錄
頁數
目錄……………………………………………………………………Ⅰ
表目錄………………………………………………………………Ⅲ
圖目錄…………………………………………………………………Ⅳ
中文摘要………………………………………………………………Ⅵ
英文摘要………………………………………………………………Ⅶ


第一章　緒論……………………………………………………………1
1-1前言………………………………………………………1
1-2文獻回顧……………………………………………………3
1-3高爾夫球具名詞解釋………………………………………6
1-4研究動機與目的…………………………………………11
1-5使用軟體簡介……………………………………………12
第二章　研究理論……………………………………………………13
2-1前言…………………………………………………………13
2-2複合材理的理論與假設……………………………………13
第三章　有限元素模型建立及分析流程……………………………20
3-1前言…………………………………………………………20
3-2高爾夫球桿模型尺寸………………………………………20
3-3元素的選擇…………………………………………………21
3-4材料的設定…………………………………………………22
3-5疊層的設定…………………………………………………23
3-6測試條件設定………………………………………………29
3-6-1 Tipflex……………………………………………29
3-6-2 Buttflex……………………………………………31
3-6-3 Torque………………………………………………33
3-6-4 C.P.M.………………………………………………35
第四章　結果與討論…………………………………………………38
4-1前言…………………………………………………………38
4-2模擬結果與實驗比對……………………………………38
4-3疊層角度變化………………………………………………39
4-4 Tipflex結果與討論………………………………………40
4-4-1內層角度變化的影響……………………………………40
4-4-2中層角度變化的影響……………………………………42
4-4-3外層角度變化的影響……………………………………44
4-5 Buttflex結果與討論………………………………………46
4-5-1內層角度變化的影響……………………………………46
4-5-2中層角度變化的影響……………………………………48
4-5-3外層角度變化的影響……………………………………50
4-6 Torque結果與討論………………………………………52
4-6-1內層角度變化的影響……………………………………52
4-6-2中層角度變化的影響……………………………………54
4-6-3外層角度變化的影響……………………………………56
4-7 C.P.M.結果與討論………………………………………58
4-7-1內層角度變化的影響……………………………………58
4-7-2中層角度變化的影響……………………………………60
4-7-3外層角度變化的影響……………………………………62
第五章　結論與未來研究方向………………………………………64
5-1結論…………………………………………………………64
5-2未來研究方向………………………………………………66
參考文獻………………………………………………………………67

參考文獻
[1] 宋定衡，“國立體育學院教練科學研究所技術報告書”，第33-35頁，國立體育學院教練科學研究所，桃園，2003
[2] 童勝男，“高爾夫球桿生產技術手冊”，第259-269頁，台灣區體育用品工業同業公會編印，台北，1989
[3] 黃進華，“台灣碳纖維高爾夫球桿市場概況”，第160-170 頁，強化塑膠廣用新知季刊，63 期，1995
[4] 魏玉珍，“假貨真「禍」防不勝「仿」”，第92-96 頁，高爾夫文摘，6月號，1999
[5] Horwood, G. P.,“Golf shaft-a technical perspective”, Science and Golf(Ⅱ):Proceedings of the 1994 world scientific congress of golf,1994
[6] Mizuno Corporation,“Golf Equipment Guide 1995”,pp. 14,1995
[7] Takayuki Matsumoto,Akiyoshi Kojima,Hideyuki Horii,and Michihiro Mohri,“Golf Club Shaft Application of High Modulus Pitch-Based Carbon Fiber”,International SAMPE Symposium and Exhibition (Proceedings),Vol.41,No.1,pp. 405-414,1996
[8] 王栢村，洪研庭，劉文全，“碳纖維高爾夫球桿材料機械性質探討 ”，第63-69頁，第十一屆中華民國振動與噪音工程學術研討會，基隆，2003
[9] Cheong, S. K.,Kang, K. W.,and Jeong, S. K.,“Evaluation of The Mechanical Performance of Golf Shafts” Engineering Failure Analysis,Vol.13, pp.464-473,2006
[10] Mizoguchi Masato,Hashiba Toshinao,Yoneyama Takeshi,“Effect of Shaft Length On The Club Head Speed In Golf”,C- Hen/Transactions of the Japan Society of Mechanical Engineers, Part C，pp.966-971,2001
[11] 王栢村，廖學任，李建興，“不同材料模型於碳纖桿之機械性質探討”，第386-392頁，第十三屆中華民國振動與噪音工程學術研討會，2005
[12] Worobets JT,Stefanyshyn DJ,“Shaft Stiffness Significantly Influences Golf Clubhead Speed At Impact”,Journal of Biomechanics ,Vol.40, pp.279,2007
[13] 陳鍵智，“高爾夫球桿揮擊動態系統分析”，國立中山大學碩士論文，2002

[14] 蘇俊憲，“高爾夫球桿之揮擊分析”，國立中山大學碩士論文，2003
[15] 周宏憲，“複合板層間應力之混合型有限元素分析”，國立中山大學碩士論文，1990
[16] 李嘉富，“簡易混合型元素的複材層間應力分析”，國立中山大學碩士論文，1991
[17] Reddy,J. N.,“Mechanics of Laminated Composite Plates Theory and Analysis”,CRC Press,Vol.1, pp.95-154,1997
[18] Ochoa,O. O. and Reddy,J. N.,“Finite Element Analysis of Composite Laminates”, Kluwer Academic Publishers, Vol.13,pp.1-24,1992
[19] 宋宜駿，“複材自行車架重新設計與力學分析”，國立中山大學碩士論文，2005